|
Hylar® 5000
聚偏二氟乙烯
Solvay Specialty Polymers
產品說明
Hylar 5000 is a crystalline high molecular weight powder form of polyvinylidene fluoride specifically designed for solvent-based coatings to provide improved gloss. It forms mechanically strong and tough films that have a broad useful temperature range. These films are highly resistant to most environmental conditions including gamma radiation and are essentially transparent to ultraviolet radiation. The weathering characteristics of Hylar 5000 coatings lead to excellent performance for the long term.
Hylar 5000 is available only via a licensing program that specifies the composition of Hylar 5000 coatings. A properly formulated finish contains sufficient pigment to make the film totally opaque to ultraviolet radiation at the nominal one mil (0.001 inch) film thickness suggested.
Safety
Hylar 5000 is stable at temperatures up to 600°F (316°C). When it is subjected to temperatures above 600°F (316°C) for extended periods of time, hydrogen fluoride (HF) begins to evolve, and at temperatures above 700°F (371°C) HF evolution becomes rapid. Hylar 5000 exhibits excellent flame resistance; however, in case of fire, HF and traces of potentially toxic fluorocarbons can be formed. HF is corrosive, causes burns on contact, and has an American Conference Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV-TWA) of 3 ppm (2.5 mg/m³) (1984).
Thermal decomposition of Hylar 5000 to HF can also occur in a bake oven in the event that temperatures are not controlled properly. In the event of fire, use NIOSH approved self-contained breathing apparatus and skin protection to protect against volatile decomposition products. Hylar 5000 can be disposed of in an approved land fill, but should not be incinerated unless permitted by applicable law and provision is made for absorption of HF.
總體
材料狀態 • 已商用：當前有效
供貨地區 • 北美洲 • 歐洲
• 純凈/高純度 • 抗輻射性 • 氣味低到無
性能特點 • 高分子量 • 抗紫外線性能良好
• 光澤，高 • 良好的強度 • 韌性良好
• 結晶 • 耐氣候影響性能良好
用途 • 薄膜 • 涂敷應用
外觀 • 白色
形式 • 粉狀
加工方法 • 涂層
物理性能 額定值單位制 測試方法
比重 1.75 到 1.76g/cm³ ASTM D792
吸水率 (平衡) 0.040% ASTM D570
Purity 2 > 99.5%
含水量 - Karl Fisher 3 < 0.50%
熱性能 額定值單位制 測試方法
熔融溫度 156 到 160°C ASTM D3418
熱穩定性 4 382 到 393°C TGA
光學性能 額定值單位制 測試方法
Gardner光澤度 (60°) > 25 ASTM D523
充模分析 額定值單位制 測試方法
表觀粘度 (232°C, 100 sec^-1) 29000 到 33000Pa•s ASTM D3835
補充信息 額定值單位制 測試方法
離散度 5 5.50 ASTM D1210
|
