|
硬體部分
1. PC板之堆疊順序
|
NO.
|
6 Layers
|
8 Layers
|
10 Layers
|
12 Layers
|
|
1
|
Middle speed
|
Middle speed
|
Middle speed
|
Middle speed
|
|
2
|
CLK & High speed
|
GND
|
GND
|
GND
|
|
3
|
GND
|
CLK & High speed
|
CLK & High speed
|
CLK & High speed
|
|
4
|
Vcc
|
GND
|
CLK & High speed
|
CLK & High speed
|
|
5
|
Others
|
Vcc
|
GND
|
CLK & High speed
|
|
6
|
CLK & High speed
|
CLK & High speed
|
Vcc
|
GND
|
|
7
|
|
GND
|
Others
|
Vcc
|
|
8
|
|
Others
|
CLK & High speed
|
Others
|
|
9
|
|
|
GND
|
CLK & High speed
|
|
10
|
|
|
Middle speed
|
CLK & High speed
|
|
11
|
|
|
|
GND
|
|
12
|
|
|
|
Middle speed
|
Remark: 1. CLK & High speed: 30MHz以上.
2. Middle speed: 10—30MHz.
3. Others: 10MHz以下.
2. PC板應保持完整性, 以正方形或長方形為最佳, 避免有缺口或不規則.
3. PC應以一塊為最佳, 避免多塊組合.
4. PC板之板邊應有3mm以上之trace來圍繞,Ground trace以10-15mm的距離,並以random方式加through hole.
5. PC板之板邊應有3mm以上之trace來圍繞,並加SMD Finger與PC板下之金屬表面接觸.
1. ALL signals應與板邊GND Trace及固定孔之距離為2mm.
2. Mother board上,至少要有7個以上之固定孔,並力求平衡,不要集中在一處.而其他區域則無螺絲孔可供下地,此螺絲孔應靠近I/O connector及VGA IC, Clock generator, DC IN.
3. All PC板之固定孔,必須導通,不能將PAD除掉.
4. Glide Pad的PC板上之signal line務必包地.
5. 每一I/O Chip set,需要放置在I/O Port之最近位置.VGA port & TV port & S terminal port需放置在一起.
6. All I/O ports之GND plane要切割.
7. VGA chip & Clock Generator務必將GND給予切割.
8. ALL I/O ports之EMI components,分別以2mm之距離,靠近I/O connector位置.
9. ALL I/O connector之固定腳PAD,再加2mm.
10. 高速訊號線& Clock trace應放至內層,並靠近GND Plane.
11. Clock trace若無法包地,其Trace & Trace之spacing是Trace的兩倍.
12. Clock generator and Main chip set在placement時不可放在板邊,應放置在中間.
13. 各chip set的信號線,其trace越短越好,clock trace須包地,頻率越高,trace越短.
14. 各chip set的信號線在走線時,不可平行重疊在一起,須垂直走線.
15. LAN & MODEM Jack至Connector之trace,其附近之每一層,不宜走線,並且Connector之外5mm應掏空.
16. Modem & LAN card, Combo card with Modem & LAN應儘量靠近LAN & Modem Jack connector. Modem & LAN Cable應走板邊,並避開DC/DC components & High Frequency components.
17. 若ESD可直接打入訊號點,則應予以絕緣包之或圍Ground Trace做保護.
|
